01-Feb-2013
0400015606
I have read and understood the disclaimer below
and wish to download the designated software
You can use this program to update the printer firmware version.
Modifications from Ver.1.40 to Ver.1.41
1. Fix the hung up issue rarely occurs when going into sleep mode.
2. Fix the paper jam with plain paper which rarely happens at the leading edge of roll paper.
3. The problem that the community name setting in SNMP setting was not processed correctly has been fixed.
4. Shutdown timer function has been added.
-Shutdown timer
After the printer goes into Sleep Mode, power will be turned off automatically when the situation that the printer is not operated continues until the time being set in advance by operation panel.
Setup time:OFF/ 5 min./ 10 min./ 30 min./ 1 hour/ 4 hours/ 8 hours*/ 12 hours *Initial value when updating version.
Note:
To fix the issue 2., please apply the MCT versions below to the printer and its driver after upgrading the firmware.
Windows 32bit 2.7205
Windows 64bit 2.7205
Mac OS X v10.4-v10.7 2.75
Mac OS X v10.2-v10.3 2.7405
Modifications from Ver.1.37 to Ver.1.40
1. The acquisition of serial number of main body by iWEMC supported
2. The failure of retrieving from sleep mode on rare occasions fixed
3. The failure of inability to print in HP/GL2 printing when file name contains 2-byte character(s) and the second byte is "5C" (back slash) fixed
4. The drive control in printing optimized
Modifications from Ver.1.36 to Ver.1.37
1. Support for obtaining printer serial numbers by iWEMC
Modifications from Ver.1.32 to Ver.1.36
1. In case the nozzles are clogged, formerly you would stop printing and check the printout,
and then continue printing by pressing the Online key.
Now it automatically checks the level of clogging, and if it is possible to print it will continue printing,
and if it needs a printhead replacement, it will display a Replace Printhead message.
This modification will greatly improve the workability.
2. Functions in the HP-GL/2 mode have been improved (to become faster).
Use this program with the systems and the operating environments below.
Software: Microsoft Windows 8 32-bit edition, English edition
Microsoft Windows 7 32-bit edition, English edition
Microsoft Windows Server 2008 32-bit edition, English edition
Microsoft Windows Vista 32-bit edition, English edition
Microsoft Windows Server 2003 R2 32-bit edition, English edition
Microsoft Windows Server 2003 32-bit edition, English edition
Microsoft Windows XP Professional / Home Edition 32-bit edition, English edition
Microsoft Windows 2000 Professional /Server , English edition
Hardware: Any computer running the software listed above.
Interface Connectivity:
The printer and computer where this program is executed must be connected
with either of the following methods.
- Connected via a TCP/IP network and capable of printing via the network.
- Connected via a USB or IEEE 1394 port cable and capable of printing
as a local printer.
Note: If you are using IEEE1394, IEEE1394 Class Driver Ver2.0 or later is
needed.
The following limitations apply to the use of this program.
Before using the program, make sure that you understand these limitations.
* You must log into Windows as an Administrator before the installation.
* Before you start the firmware version update program, close any other applications
that are running.
* Do not try to use the printer while the firmware version update program is running.
If a print job is executing, cancel the print job or wait for the job to finish
before you execute the version update program.
* Never switch off the target printer while the firmware version update program is running.
* If the firmware version update fails while writing to the flash ROM,
you may not be able to start the printer. In this case,
contact a Canon service center or the dealer where you purchased the printer.
(1) Switch the printer on.
(2) Decompress it on your computer hard disk.
(3) Execute the setup file. The imagePROGRAF Firmware Update Tool is installed.
(4) From the Start menu, select Programs to execute imagePROGRAF Firmware Update Tool.
All software, programs (including but not limited to drivers), files, documents, manuals, instructions or any other materials (collectively, “Content”) are made available on this site on an "as is" basis.
Canon Marketing (Philippines) Inc., and its affiliate companies (“Canon”) make no guarantee of any kind with regard to the Content, expressly disclaims all warranties, expressed or implied (including, without limitation, implied warranties of merchantability, fitness for a particular purpose and non-infringement) and shall not be responsible for updating, correcting or supporting the Content.
Canon reserves all relevant title, ownership and intellectual property rights in the Content. You may download and use the Content solely for your personal, non-commercial use and at your own risks. Canon shall not be held liable for any damages whatsoever in connection with the Content, (including, without limitation, indirect, consequential, exemplary or incidental damages).
You shall not distribute, assign, license, sell, rent, broadcast, transmit, publish or transfer the Content to any other party. You shall also not (and shall not let others) reproduce, modify, reformat, disassemble, decompile or otherwise reverse engineer or create derivative works from the Content, in whole or in part.
You agree not to send or bring the Content out of the country/region where you originally obtained it to other countries/regions without any required authorization of the applicable governments and/or in violation of any laws, restrictions and regulations.
By proceeding to downloading the Content, you agree to be bound by the above as well as all laws and regulations applicable to your download and use of the Content.