Solution
Setting the IP address to the machine allows it to communicate with computers on the network.
The followings are the procedures for specifying the IP Address settings. If you set IP address automatically using such as DHCP, you can confirm the IP address settings by performing the procedure in "Confirming IP Address Settings" after configuring the IP Address settings.
NOTE
- Before performing the following procedure, make sure that the machine is turned on and connected to a network.
- This machine is set by default to automatically draw an IP address using DHCP. If your network server or router is configured to provide a DHCP address, all you need to do is connect a network cable and turn on the machine. The machine will draw an IP address automatically.
- This machine also supports automatic IP addresses using BOOTP and RARP protocols. If you use these protocols, then specify the <BOOTP> or <RARP> in the procedure of "Setting IP Address Automatically."
Setting IP Address Automatically
The followings are the procedures for specifying the IP address automatically.
The default settings are as follows :
- <IP ADDRESS> : <ON>
- <DHCP> : <ON>
- <BOOTP> : <OFF>
- <RARP> : <OFF>
1. Press
[Menu].
2. Press
or
to select <SYSTEM SETTINGS>, then press [OK].
If the System Manager ID and System Password have been set, enter the System Manager ID and System Password using
–
[numeric keys], then press
[Log In/Out].
3. Press
or
to select <NETWORK SETTINGS>, then press [OK].
4. Press
or
to select <TCP/IP SETTINGS>, then press [OK].
5. Press
or
to select <IP ADDRESS AUTO.>, then press [OK].
6. Press
or
to select <ON>, then press [OK].
7. Press
or
to select the desired protocol, then press [OK].
- <DHCP>: The machine obtains the necessary information for communication via DHCP.
- <BOOTP>: The machine obtains the necessary information for communication via BOOTP.
- <RARP>: The machine obtains the necessary information for communication via RARP.
8. Press
or
to select <ON>, then press [OK].
NOTE
You can select <ON> or <OFF> for each protocol independently. If the protocol you don't want to use is set to <ON>, you need to set it to <OFF>.
Setting IP Address Manually
The followings are the procedures for specifying the IP address manually.
The default settings are as follows :
- <IP ADDRESS> : <000.000.000.000>
- <SUBNET MASK> : <000.000.000.000>
- <GATEWAY ADDRESS> : <000.000.000.000>
1. Press
[Menu].
2. Press
or
to select <SYSTEM SETTINGS>, then press [OK].
If the System Manager ID and System Password have been set, enter the System Manager ID and System Password using
–
[numeric keys], then press
[Log In/Out].
3. Press
or
to select <NETWORK SETTINGS>, then press [OK].
4. Press
or
to select <TCP/IP SETTINGS>, then press [OK].
5. Press
or
to select <IP ADDRESS AUTO.>, then press [OK].
6. Press
or
to select <OFF>, then press [OK].
7. Press
or
to select <REG. IP ADDRESS>, then press [OK].
8. Press
or
to select <IP ADDRESS>, then press [OK].
9. Use
–
[numeric keys] to enter the IP address, then press [OK].
10. Press
or
to select <SUBNET MASK>, then press [OK].
11. Use
–
[numeric keys] to enter the subnet mask, then press [OK].
12. Press
or
to select <GATEWAY ADDRESS>, then press [OK].
13. Use
–
[numeric keys] to enter the gateway address, then press [OK].
14. Turn OFF the main power on the right side of the machine, then turn ON the power to restart the machine.
Confirming IP Address Settings
To confirm IP address settings, follow the procedure below.
1. Press
[Menu].
2. Press
or
to select <SYSTEM SETTINGS>, then press [OK].
If the System Manager ID and System Password have been set, enter the System Manager ID and System Password using
–
[numeric keys], then press
[Log In/Out].
3. Press
or
to select <NETWORK SETTINGS>, then press [OK].
4. Press
or
to select <TCP/IP SETTINGS>, then press [OK].
5. Press
or
to select <VIEW IP ADDRESS>, then press [OK].
6. Press
or
to select <IP ADDRESS>, <SUBNET MASK>, or <GATEWAY ADDRESS> for displaying the setting you want to check, then press [OK].
7. Press
[Stop/Reset] to return to the standby mode.
