How to perform the wireless LAN setup manually (Macintosh)
07-Jul-2010
8200796300
Solution
Before connecting the machine to the network, make sure that the computer and access point or router is connected.
Add (connect) the machine to the network.
NOTE
An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without using an access point, is not supported. Be sure to prepare an access point.
- Notes on Wireless Connection
- The configuration, router functions, setup procedures and security settings of the network device vary depending on your system environment. For details, refer to your device's instruction manual or contact its manufacturer.
- In an office setup, consult your network administrator.
- If you connect to a network that is not protected with security measures, there is a risk of disclosing data such as your personal information to a third party.
- If an error message appears or if you have trouble with the network connection, refer to the printed manual: Network Setup Troubleshooting.
- Place the machine and computer on the same network segment.
To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk. The installation process takes about 20 minutes. (The installation time varies depending on the computer environment or the number of application software to be installed.)
IMPORTANT
- Quit all running applications before installation.
- Log on as the administrator (or a member of the Administrators group).
- Do not switch users during the installation process.
- Internet connection may be required during the installation. Connection fees may apply. Consult the internet service provider.
- It may be necessary to restart your computer during the installation process. Follow the on-screen instructions and do not remove the Setup CD-ROM during restarting. The installation resumes once your computer has restarted.
- If the firewall function of your security software is turned on, a warning message may appear that Canon software is attempting to access the network. If such a warning message appears, set the security software to always allow access.
- For the system requirements, refer to "Specifications".
Do not connect the wireless LAN setup cable yet.
Software installation requires temporary use of the wireless LAN setup cable.
1.
Turn on the computer, then insert the Setup CD-ROM into the CD-ROM drive.
If you are using Windows, the setup program starts automatically.
2.
Double-click the Setup icon of the CD-ROM folder to proceed to the following screen. Enter your administrator name and password, then click OK.
If the CD-ROM folder does not open automatically, double-click the CD-ROM icon on the desktop.
If you do not know your administrator name or password, click the help button, then follow the on-screen instructions.
3.
Select your place of residence, then click Next.
NOTE
If the Select Language screen appears, select a language, then click Next.
4.
Select a country or region, then click Next.
5.
Click Easy Install.
The drivers, application software, and on-screen manuals are installed.
NOTE
If you want to select particular items to install, click Custom Install.
6.
Click Install.
7.
Select Use the printer on network, then click Next.
Follow any on-screen instructions to proceed with the software installation.
8.
When the Printer Detection screen appears, click Next.
IMPORTANT
- If the Printer Connection screen appears instead of the screen above, the connection method is not correctly selected in 7.
Follow on-screen instructions and proceed with the installation. Click Exit on the installation complete screen, then start again from 2 and be sure to select Use the printer on network in 7.
9.
Make sure the machine is turned on, then click OK.
10.
When the Set Up New Printer screen appears, click Next.
NOTE
If the Detected Printers List screen appears, click Set Up New Printer.
11.
When the Connect Cable screen appears, connect the machine to the computer with the wireless LAN setup cable.
Follow the on-screen instructions and click Next.
12-A.
- If the Detected Access Points List or Access Points screen appears
If the screen below does not appear, perform 12-B.
(1)Select the target access point name/network name (SSID).
(2)Enter the network key.
Enter upper and lower case letters of the alphabet correctly.
Letters are case sensitive.
To use WEP key number 2, 3 or 4, click WEP Key Number, then specify the WEP key number.
(3)Click Connect.
->Go to 13.
NOTE
- If the target access point is not displayed on the Detected Access Points List or Access Points screen, refer to the printed manual: Network Setup Troubleshooting.
- For details on how to check the access point name/network name (SSID) and network key, refer to the manual supplied with your access point or contact its manufacturer.
SSID
An identifier to identify the specific access point.
Network Key
Also referred to as encryption key, WEP key or WPA/WPA2 passphrase, Pre-Shared key.
A password required to set to prevent unauthorized access to communication.
12-B
- If the Confirm Connection Access Point screen appears
Make sure that the target access point is displayed, then click Yes.
If you are using Macintosh, a screen asking for permission to access the keychain appears. In this case, click Allow or Allow Once.
->Go to 13.
NOTE
If the target access point is not displayed in the above screen, click No, then perform 12-A.
13.
When the Disconnect Cable screen appears, remove the wireless LAN setup cable, then click Next.
NOTE
If the Automatic Setup or Auto Setup screen appears, click OK, then perform 12-A.
14.
When the Setup Completion screen appears, click Complete or OK.
This section describes how to register the machine on a Macintosh computer.
NOTE
- The alphanumeric characters after Canon MP495 series is the machine's Bonjour service name or MAC address.
- If the machine has not been detected, make sure of the following.
- The machine is turned on.
- The firewall function of any security software is turned off.
- The computer is connected to the access point.
1.
When the Register Printer and Scanner screen appears, click Register Printer.
Mac OS X v.10.6.x ->Go to 2-A.
Mac OS X v.10.5.x ->Go to 2-A.
Mac OS X v.10.4.11 ->Go to 2-B.
2-A.
(1)
Select Canon MP495 series canonijnetwork and click Add.
2-B.
(1)
When the Printer List window appears, click Add.
NOTE
When the You have no printers available. screen appears, click Add.
(2)
Click More Printers in the Printer Browser window.
(3)
Select Canon IJ Network in the pop-up menu, select Canon MP495 series in the list of printers, then click Add.
(4)
Make sure that Canon MP495 series is added to the list of printers.
-> Go to 3.
3.
When the Register Printer and Scanner screen appears, click Register Scanner.
4.
Select Canon MP495 series on the Scan-from-PC Settings screen, then click OK.
5.
Click Next on the Register Printer and Scanner screen.
1.
Click Next.
Follow any on-screen instructions to proceed with the software installation.
Important Information for the Installation
- Necessary Information for the User Registration
When the serial number is not displayed on the registration screen automatically, input the serial number located inside the machine (as shown in the illustration).
IMPORTANT
If the power is on, the FINE Cartridge Holder will move when the Scanning
Unit (Cover) (A) is opened.
- If the Extended Survey Program screen appears
If you can agree to Extended Survey Program, click Agree.
If you click Do not agree, the Extended Survey Program will not be installed. (This has no effect on the machine's functionality.)
2.
Click Exit to complete the installation.
It is necessary to restart the computer before scanning using the Operation Panel on the machine for the first time.
3.
Solution Menu EX starts when clicking OK in the Canon Solution Menu EX dialog.
Remove the Setup CD-ROM and keep it in a safe place.
NOTE
The buttons displayed on Solution Menu EX may vary depending on the country or region of purchase.
- Using the Machine from Additional Computers
Now that the wireless connection of the machine is complete, it can be used from additional computers on the same network.
Install software including the drivers on the computer from which you want to use the machine. Other settings are not required.
To add computers from which to use the machine, go to "Use from Additional Computers" .
If the machine is already connected to a wireless connection, it can be used from additional computers on the same network.
To use from additional computers
1. Insert the Setup CD-ROM into the computer from which you want to use the machine.
2. Follow the on-screen instructions to install the software.
Other settings are not required.
For details on the software installation procedure, refer to "How to perform the wireless LAN setup so that other computers can share the same printer (Macintosh)".